20 November 2026 · Yotters, independent yacht media
Yotters
Products & Luxury

Lenco Marine

Lenco Marine is the Stuart, Florida maker of the electric trim tab kits that sit on the transoms of a large share of American centre consoles, express cruisers and trawlers. It dates from 1986, passed through Power Products to Brunswick in 2018 and now sits in Navico Group. Its 2024 Pro Control system uses ordinary tabs to hold pitch and roll, and the one detailed independent test we found says it has the lowest ceiling of the three systems compared and drops out in head seas.
A pair of Lenco electric trim tabs with their actuators, shown in the maker's product images.
A pair of Lenco electric trim tabs with their actuators, shown in the maker's product images.Photo: Lenco Marine (press material)
Lenco Marine, Stuart, Florida; founded 1986 with Richard DeVito named as co-founder (Power Products announcement, December 2016; Lenco's own brand page also says since 1986)
Power Products bought Lenco in December 2016, price not disclosed (Marine Link, 20 December 2016; Trade Only Today, 21 December 2016)
Brunswick completed its USD 910 million cash purchase of Power Products' Global Marine and Mobile business on 9 August 2018, with Lenco one of 11 brands (Boating Industry, August 2018)
Lenco now sits in Navico Group, a Brunswick division, and its site lists trim tabs, Pro Control, actuators, controls, surf and hatch lifts
Standard, edge mount, high performance, super strong, hybrid, extreme duty and heavy duty tab kits, in 12 V and in some cases 24 V (Lenco site)
High Performance single kit for 16 to 40 ft, dual for 24 to 52 ft; Heavy Duty for 18 to 42 ft; Pro Control Auto kits for 16 to 30 ft and 17 to 30 ft (Lenco site)
Auto Glide, the older automatic controller, needs Lenco tabs with electric actuators and reads the running angle about 25 times a second (Seaknights; Lenco listing)
Pro Control launched in 2024 and won an Innovation Award at IBEX 2024; Lenco claims 74 percent better roll control than the hull alone (Panbo, May 2025)
Panbo's 2025 teststrong on roll and launch, drops out of auto in head or bow-quartering seas and leaves tabs where they were; IMU dropouts began about two months after install
Typical street prices in November 2026about USD 653 for a 12 x 12 kit with no switch, about USD 1,836 for Pro Control Assist, USD 2,867 to 2,921 for Pro Control Auto

Where Lenco comes from

The founding year comes from the 2016 announcement of the sale to Power Products. Power Products chief executive David Scheer called Lenco a recognised leader since its founding in 1986, and Richard DeVito is named there as the co-founder who said he was pleased to partner as Lenco went to the next level of growth. Trade Only Today ran that story on 21 December 2016 and Marine Link carried it a day earlier. The price wasn't disclosed and Lenco was to keep operating in Stuart under its current leadership. A retailer page gives 1980 as the founding year and credits Lenco with the first fully electric tab system; we found nothing to back either claim, so we use 1986 and leave the first-electric claim out.

Less than two years later the parent changed again. Brunswick announced in June 2018 that it would buy Power Products' Global Marine and Mobile business from the private equity owner Genstar Capital for USD 910 million in cash and completed it on 9 August 2018. Lenco was one of 11 brands in the deal, alongside Ancor, Blue Sea Systems, Mastervolt and Marinco, and the business joined Mercury Marine's parts and accessories group. Power Products' revenue for the 12 months to March 2018 was about USD 233 million across all 11 brands. Lenco's current site calls it part of Navico Group, a Brunswick division, and says it has more than 30 years of experience.

What a Lenco kit is and which size fits

A kit is two flat stainless or coated blades, one actuator for each, a helm switch or controller, and wiring. Lenco's current range runs from Standard Mount and Edge Mount kits, which come with a switch, through High Performance kits with contoured blades meant to reduce cavitation, a Super Strong dual-actuator kit with longer blades in 12 V and 24 V, a Hybrid kit with double actuator support, an Extreme Duty kit with a lower actuator mount and a Heavy Duty kit. The site gives boat lengths rather than blade sizes. High Performance is listed for 16 to 40 ft with a single actuator per tab and 24 to 52 ft with a dual one, Extreme Duty for 14 to 36 ft in standard finish and 14 to 30 ft in electro-polished, and Heavy Duty for 18 to 42 ft. An airboat kit exists too.

Retailers list the blades by inches, for example 9 x 12 standard, 12 x 12 edge mount and 14 x 12 or 21 x 14 high performance, and a Pro Control actuator is listed at a 750 lb load rating. The 24 V options matter on larger boats whose systems run at 24 V. The practical rule is that a heavy, stern-heavy boat wants a bigger blade or a dual actuator, and an owner who simply bolts on the smallest kit will be disappointed. The Ranger Tug owners quoted below say the stock tabs on a stern-heavy 27 foot boat were about half as effective as they wanted.

Cheapest way to automate tabs you already own, and the lowest ceiling of the three systems in the one detailed test.

Auto Glide, the older automatic controller

Lenco has sold AutoGlide since at least 2016, when the Power Products announcement named it. Seaknights, a review site, says it measures the boat's running angle about 25 times a second, aims to remove bow bounce, reduce bow rise at the hole shot and find an efficient running angle. The kit has a control box for a single actuator, a keypad, an NMEA 2000 GPS antenna and the cabling; a dual actuator box, 30 to 50 ft adapter cables and a GPS box bracket are extra. The same review says it performed comparably to Bennett's AutoTrim Pro, but gives no method or data, so read it as an opinion and not a test.

Bennett's own marketing page, last updated March 2026, calls Autoglide too expensive for many owners and says AutoTrim Pro costs about half as much and can be fitted to other brands' tabs, Lenco's included. That is a competitor's claim and we found no list price on it. Some owners already have the data feed: a Ranger Tugs owner on the Tugnuts forum noted in 2022 that those boats come with NMEA 2000 and GPS, so only the actuator box was needed. Retail listings for the aftermarket kit in Australia showed AU$3,590.60 with GPS and AU$2,693.80 without in November 2026.

A sport boat on the plane at sunset, from Lenco's own site; the maker shows its tabs on boats of this type.
A sport boat on the plane at sunset, from Lenco's own site; the maker shows its tabs on boats of this type.Photo: Lenco Marine (press material)

Pro Control, the 2024 system

Lenco launched Pro Control Auto in September 2024 and it won an Innovation Award at IBEX 2024. It has an Assist version that is manual with planing assist, automatic tab retract and stored favourite positions, and an Auto version that levels the boat. The kits listed on Lenco's site are the Pro Control Auto Standard Mount for 16 to 30 ft and the Edge Mount for 17 to 30 ft. Lenco claims a 74 percent roll improvement against the hull alone and says it beats the leading interceptor system by 25 percent. Ben Stein of Panbo, who sat on the IBEX judging panel, wrote in May 2025 that he had not been able to get the data behind the 25 percent claim and that the system he compared was Seakeeper Ride.

Stein fitted it to his 2017 Edgewater 280CX. He reused his tabs but replaced the helm controller, the actuators and wiring, and added an inertial measurement unit. The new actuators use the same bolt pattern, but the transom bracket went from three to four screws, so his triangular tab pockets kept the old brackets. He called it the first traditional tab system he had tested that actively controls both pitch and roll. In roughly 26 knots and one foot seas the launch control kept the bow down and the boat level and roll reduction was strong, though pitch reduction was smaller. Corrections felt natural, he said, unlike Zipwake, but automatic corrections can induce yaw, which grows with larger rolls.

Where it falls short

In head or bow-quartering seas the system took hard hits and dropped out of automatic mode, Stein wrote, and the tabs stayed in their last position, sometimes unevenly, which gave an unsafe running angle. In large beam seas it could not react fast enough and it did little for slamming at speed, which he says Seakeeper Ride handles well. His 28 July 2025 update says the IMU produced bad data from about two months after install, causing dropouts, and that engineers from Lenco, Navico and Brunswick were working on it and had not fully fixed it. He judged Pro Control to have the lowest ceiling of the three systems he discussed and a good fit for fair-weather boating rather than rough offshore work. The interface was button-hold menus with LED codes, less intuitive than Zipwake's display.

Tabs have old problems too. On Yacht Forums in April 2014 a poster called Capt J said Lenco tabs suit centre consoles kept on a lift and not boats left in the water, claiming huge electrolysis problems. In March 2014 another poster, Capt Ralph, said Lenco has a good product but advised against it for boats left in the water after seeing failures at the hinge spot welds. These are two anecdotes from 2014, and the tab designs have changed since, but they are the only corrosion reports we found, so ask the dealer about bonding and anodes.

How it compares with interceptors and Bennett

A trim tab pushes water down with a flap that hinges out behind the transom; an interceptor is a blade that drops vertically, which Yotters covers on its Zipwake and Humphree pages. Stein says Pro Control costs half or less than the other trim and roll systems he discusses, and that is its case: it reuses the tabs already on the boat and needs no through-hull work beyond new actuators and a sensor. He rates the other two systems' ceiling higher. Bennett says it invented tab technology in 1959 and auto tab control in 1992, and that AutoTrim Pro arrived in 2016 and works with other makers' tabs; these are Bennett's dates and we did not check them independently.

The choice mostly follows the boat. A planing centre console or express cruiser in fair water with Lenco tabs already fitted is the natural Pro Control or Auto Glide buyer. A slow displacement hull gains little from either. A heavy boat in head seas should look at an interceptor system, and a boat that stays in the water for years should ask about corrosion and the five-year warranty Lenco's site lists, whose terms we did not read.

Practical detail

Price, manual kitsAbout USD 653 for a 12 x 12 standard kit without switch (Freeport Marine listing) and USD 886 for a 12 x 12 edge mount with switch (Walmart listing), seen November 2026
Price, Pro ControlAssist 12 x 12 listed at USD 1,836 (Alltackle) and the Auto kit at USD 2,867 to 2,921 (Defender, listed out of stock); launch price reported as USD 2,650 in a January 2025 BoatUS item, which the desk could not open and has not verified
Price, Auto GlideAU$3,590.60 with GPS and AU$2,693.80 without at an Australian retailer, November 2026; no US list price found
CompareBennett AutoTrim Pro, which Bennett says costs about half of AutoGlide; Zipwake and Humphree interceptors on their own Yotters pages
FitHigh Performance 16 to 40 ft single or 24 to 52 ft dual; Heavy Duty 18 to 42 ft; Pro Control Auto 16 to 30 ft or 17 to 30 ft; 12 V, some 24 V
InstallationPro Control needs new actuators, helm controller and an IMU; the transom bracket may change from three to four screws; fitted by Panbo on an Edgewater 280CX
Check before buyingBoat length and weight against the kit; whether the boat is kept in the water; bonding and anodes; NMEA 2000 and GPS already aboard; warranty terms
What is not publishedBlade dimensions by kit on Lenco's page, any independent fuel saving test, the data behind the 74 percent and 25 percent claims, current US list prices and warranty terms

What owners and crew report

What is good, and what to watch

Strong points

  • Cheapest route to automatic trimReuses existing tabs; Panbo estimates half or less than other trim and roll systems; a 12 x 12 manual kit lists around USD 653 to 886
  • Wide range of kitsStandard to extreme duty, 12 V and 24 V, for roughly 14 to 52 ft, with an OEM and aftermarket supply chain
  • Strong roll control in moderate waterPanbo reports strong roll reduction and a good launch assist at 26 knots in one foot seas
  • Big owner company behind itPart of Navico Group and Brunswick, with engineers working on the sensor issue

What to watch

  • Drops out in head seasPanbo says the tabs stay in the last position, sometimes unevenly, creating an unsafe running angle
  • Sensor reliabilityIMU data problems two months after install, unresolved in the July 2025 update
  • Little effect on slammingPanbo says it does little against hard impacts at speed, unlike Seakeeper Ride
  • Older corrosion reportsTwo 2014 forum posts on hinge welds and electrolysis for boats left in the water
  • Calibration and tab sizeOwners report calibration trouble, fuel economy loss and tabs too small for light boats

Who it is for: Owners of planing boats with Lenco or similar tabs who want automatic trim without cutting new holes, and buyers comparing it against Bennett and interceptor systems.

Profile compiled by Yotters from public sources.
Yotters DeskEditor-in-Chief: Leon SolimanEditorial standards
Reported from primary sources: Panbo, Trade Only Today, Marine Link, Boating Industry, Tugnuts, Yacht Forums, Seaknights, Navico Group, Bennett Marine, Lenco Marine.

More in Products

Products

Pascoe International

Products

Cantiere Nautico Cranchi

Products

SEABOB (Cayago)

Partner with Yotters

Product and luxury brands belong on Yotters.

List your brand, claim your profile, or plan a campaign with the desk that owners, brokers and builders read first.

I am interested in Products

The Yotters Brief

The yacht world, read every morning.

The stories that move the yacht world, before the market does. Join the owners, brokers and builders who start the day with Yotters.